The Belkin Titan SmartShield Pro Bright Privacy Screen Protector comes with the Easy Align tray for a simple close-and-pull installation. The tray holds the screen protector in position so you can apply it to your iPhone at home for a precise, bubble-free, and dust-free result.
This guide walks you through each step of the installation.
Compatibility
- OVA297: iPhone 18 Pro
- OVA298: iPhone 18 Pro Max
Before You Begin
Make sure you have everything included in the package:
- Titan SmartShield Pro Bright Privacy Screen Protector
- Easy Align tray
- Dust removal sticker
- Cleaning cloth
- Alcohol wipe
Important: Remove your phone case and any existing screen protector before you start. Apply the screen protector in a clean, well-lit area with as little dust as possible.
Step 1: Clean the screen
- Wipe your iPhone's screen with the alcohol wipe to remove oils and fingerprints.
- Dry and polish the screen with the cleaning cloth until no smudges or streaks remain.
Step 2: Remove any remaining dust
- Press the dust removal sticker onto the screen and lift it off to pick up any dust particles.
- Repeat across the whole screen, including the edges and around the front camera.
Tip: Hold the screen under a light at an angle to spot any dust you may have missed. Even a small particle can cause a bubble.
Step 3: Prepare the Easy Align tray
- Place the Easy Align tray on a flat surface with the screen protector facing up.
- Unfold the pull tab from the Easy Align tray and set it aside for later use. Do not pull it yet.
Step 4: Close — place your iPhone in the tray
- Hold your iPhone close to the tray.
- Flip your iPhone face down and place it into the Easy Align tray.
- Make sure your iPhone is fully seated in the tray so the screen lines up with the screen protector.
Note: Place your iPhone into the tray quickly after cleaning so no new dust settles on the screen.
Step 5: Pull — apply the screen protector
- While pressing gently on the back of your iPhone, pull the tab (liner) back toward you horizontally in one smooth motion.
- The screen protector is applied to your screen as the liner is pulled away.
Step 6: Remove your iPhone from the tray
- Slowly peel the Easy Align tray away from your iPhone.
- Turn your iPhone over and check that the screen protector is aligned with the edges of the screen.
Step 7: Smooth out any bubbles
- Use the cleaning cloth to press out any air bubbles, working from the center of the screen toward the edges.
Your iPhone is now protected by the Belkin Titan SmartShield Pro Bright Privacy Screen Protector.
Quick Troubleshooting
|
Issue |
Suggested Fix |
|
Small air bubbles |
Press them toward the nearest edge with the cleaning cloth. |
|
Dust trapped under the protector |
Make sure the screen is fully cleaned before placing your iPhone in the tray. Dust trapped under the glass cannot be removed without lifting the protector. |
|
Protector not aligned with the screen |
Confirm your iPhone model matches the product (OVA297 for iPhone 18 Pro, OVA298 for iPhone 18 Pro Max) and that the phone was fully seated in the tray before pulling the tab. |
|
Screen looks dark from the side |
This is normal. The 2-way privacy filter keeps your screen private from side angles in portrait mode. The screen is clearly visible when viewed straight on, and stays brighter than traditional privacy screen protectors. |
|
Face ID not working |
The screen protector is designed to support Face ID. Make sure the protector is aligned and the area over the front camera and sensors is clean. |
Helpful Tips
- Take your time cleaning. A clean, dust-free screen is the key to a bubble-free installation.
- Keep your fingers off the adhesive side of the screen protector.
- Pull the tab in one smooth, steady motion rather than in short tugs.
- Register your screen protector to activate your warranty by scanning the QR code on the packaging or visiting belkin.com/support/register-a-screen-protector.
Watch the Video
Prefer to follow along? Watch our step-by-step video to see how easy it is to apply your Titan SmartShield Pro Bright Privacy Screen Protector with the Easy Align tray. Watch the video here.
