How to set up the Wemo WiFi Smart Dimmer

How to tell which version of Wemo Dimmer you have

Physical installation (Wemo Dimmer F7C059 and WSD060)

Finishing the setup in the Wemo app

Wemo Dimmer F7C059 (first generation)
Wemo Dimmer WSD060 (second generation)

What does the power light color tell me?

The Wemo® WiFi Smart Dimmer, F7C059 and WSD060 make it easy for you to control your dimmable lighting anywhere you are and anytime you want.

If you are NOT familiar with electrical work, or feel uncomfortable about it, contact a professional electrician.

Watch the installation video

This video shows the installation of a Wemo Wi-Fi Smart Dimmer.

How to tell which version of Wemo Dimmer you have

The second-generation Wemo Dimmer (WDS060) has a power icon on the button while the first-generation Wemo Dimmer (F7C059) does not.

Physical Installation (Wemo Dimmer F7C059 and WDS060)

Before you begin:

Make sure your home has a neutral wire in the wall where you want to install the Wemo Dimmer. The Wemo Dimmer will not work without a neutral wire. View the wiring diagrams here.
Download and install the Wemo app. It is available at the App Store® for iOS devices and on Google Play™ for Android™ devices.
If you are installing more than one Wemo Dimmer, or if you already have another Wemo Dimmer in your home, write down the Wemo ID# found on the label at the bottom of the Wemo Dimmer. You can also find the Wemo ID on the package, right above the serial number.
Check the Wi-Fi signal on your phone at the spot where you’ll install the Wemo Dimmer to make sure the Wi-Fi is strong. Wemo only works on your 2.4 GHz wireless band.
If you have an iOS device, you’ll need iOS 11.3 or later to use the Apple® Home™ app to manage your Wemo Dimmer. If you will use only the Wemo app, you’ll need iOS 9.0 or higher.

Step 1: Turn the power OFF.

Shut OFF power to the light switch you are replacing at the circuit breaker or fuse box.

WARNING! Risk of electric shock!
Incorrect installation could be dangerous or illegal. Multiple breakers/fuses may need to be turned OFF for safe installation. Please call a professional electrician if you are unfamiliar or uncomfortable with electrical work.

Confirm that the power is turned OFF

Remove the cover plate from the existing switch. Use a voltage tester to test BOTH sides of the switch. You may need to turn OFF more than one circuit breaker/fuse.

Step 2: Find the neutral wires.

Unscrew the existing switch and gently pull it out of the wall. Look for the neutral wires, usually white. You need these to install the Wemo Dimmer. Continue ONLY if you have the neutral wires.

NOTE: You may have a different color and number of neutral wires than shown.

To see the correct wiring diagram, click here.

Test the neutral wires

Use a voltage tester to check that there is no power in the neutral wires from neighboring circuits. If necessary, shut OFF additional circuits until no voltage is found.

Disconnect the neutral wires

Unscrew the wire nut connecting the neutral wires.

Step 3: Find the ground wires.

Look for the ground wires (usually green or solid copper) and unscrew the wire nut connecting them.

NOTE: You may have a different color and number of ground wires than shown.

Step 4: Find and label the line and load wires.

Label the line and load wires. If you're unsure which wire is which, we'll help you in the next step.

NOTE: Your existing wires may be in different locations than shown.

IMPORTANT: Never label wires while the power is turned ON.

Help with distinguishing the line from load wires:

1. Disconnect the remaining wires and remove the existing switch.
2. Cap the line and load wires for safety.

3. Turn the power back ON.

IMPORTANT: Make sure not to directly touch any wires while the power is turned ON.

4. Test to identify the wires.

Use a non-contact voltage tester to distinguish the wires.

Line wire: This wire will have power because it carries electricity to the switch.
Load wire: This wire will not have power because it carries electricity from the switch to your lights.

5. Turn the power back OFF.

IMPORTANT: Verify that the power is turned OFF before proceeding.

6. Label the line and load wires.

Step 5: Connect the Wemo Dimmer wires.

IMPORTANT: Make sure the power is turned OFF before you proceed.

Remove the cover plate

After disconnecting and removing the existing switch, snap the cover plate off of your Wemo Dimmer.

Connect the line and load wires

Use a wire nut to connect the red load wire on the Wemo Dimmer to the load wire in the wall.
Use a wire nut to connect the black line wire on the Wemo Dimmer to the line wire in the wall.

NOTE: Your existing wires may have different colors than those shown.

Connect the neutral and ground wires

Use a wire nut to connect the white neutral wire on the Wemo Dimmer to the neutral wires (usually white) in the wall.
Use a wire nut to connect the green ground wire on the Wemo Dimmer to the ground wires (usually green or bare copper) in the wall.

NOTE: Your existing wires may have different colors than those shown.

Step 6: Install the Wemo Dimmer into the wall.

Almost done! Tug on each wire nut to make sure they are secure on the wires.

Carefully tuck the wires behind the Wemo Dimmer

Insert the Wemo Dimmer into the box. It could get crowded in there.

Screw the Wemo Dimmer into the wall and snap on the cover plate

Be careful not to over-tighten the screws.

NOTE: If you’re working with a second-generation Wemo Dimmer (WSD060), you’ll notice an eight-digit setup code on the Wemo Dimmer. You’ll need this during the Wemo app setup if you have an iOS device.

Step 7: Turn ON the power.

Turn ON the power on your Wemo Dimmer at the fuse panel or circuit breaker panel.

Finishing the setup in the Wemo app for Wemo Dimmer F7C059 (first generation)

The light bar on your Wemo Dimmer should start to blink white while starting up and blue when ready for the Wemo app setup.

Blinking white
User-added image

- Starting up

Blinking blue
User-added image

- Ready for Wemo app setup

NOTE: If your Wemo Dimmer did not power up, then your load and line wires may be reversed and you need to switch them.

Step 1: Go to the Wemo app for the next steps.

Download and launch the Wemo app.

Create a Wemo account in the Wemo app, then add your Wemo Dimmer. Click here to know how.

Step 2: Tell us what you're setting up.

Step 3: Choose a Wemo Dimmer model.

Step 4: Confirm the physical installation.

Step 5: Confirm that the Wemo Dimmer is ready for setup.

Step 6: Connect to the Wemo’s temporary setup Wi-Fi.

NOTE: Remote Access allows you to control your device when you are away from home. If Remote Access fails in setup, tap on Later to complete the setup without Remote Access. After the setup is complete, go to More > Remote Access and tap on Enable (make sure your mobile device is connected to your Wi-Fi).

Connecting to other services

Control your Wemo devices with voice, create groups, and more. Connect to these services in the Wemo app.

Finishing the setup in the Wemo app for Wemo Dimmer WDS060 (second generation)

The light ring on your Wemo Dimmer should start to blink white while starting up and blue when ready for the Wemo app setup.

Blinking white
User-added image

- Starting up

Blinking blue
User-added image

- Ready for Wemo app setup

NOTE: If your Wemo Dimmer did not power up, your load and line wires may be reversed and you need to switch them.

Step 1: Go to the Wemo app for the next steps.

Download and launch the Wemo app.

Create a Wemo account in the Wemo app, then add your Wemo Dimmer. Click here to know how.

Step 2: Tell us what you're setting up.

Step 3: Choose a Wemo Dimmer model.

Step 4: Confirm the physical setup.

Step 5: Confirm the Wemo Dimmer is ready for setup.

Step 6: Connect to the Wemo’s temporary setup Wi-Fi (Android) or use the HomeKit® setup code (iOS).

If you still have your quick setup guide, the HomeKit code is on a sticker in the guide. You can also find it on the Wemo Dimmer behind the faceplate.

Connecting to other services

Control your Wemos with voice, create groups, and more. Connect to these services in the Wemo app.

Adjusting your brightness level

After the setup, you can adjust the brightness level of the bulbs controlled by your Wemo Dimmer by tapping on Edit in the Devices screen of the Wemo app.